Custom

RJ45 Male Connector

Steady & Reliable Manufacturer

Overview

The RJ45 male connector — technically an 8P8C modular plug — is the small clear connector crimped onto the end of twisted-pair Ethernet cable to create a patch cord or terminate a device end. It carries eight gold-plated contacts arranged to mate with the RJ45 port on a switch, patch panel, faceplate, or NIC, and is manufactured in category-rated versions (Cat5e, Cat6, Cat6A) to match the performance needed for gigabit, 2.5G, or 10-gigabit Ethernet. RJ45 male connectors come in solid-conductor and stranded-conductor versions, shielded and unshielded housings, and traditional or feed-through (pass-through) designs, making them one of the most widely used field-termination components in structured cabling and patch cord manufacturing.

Product Catalog

Introduction

Two design families dominate the market: traditional crimp plugs, where conductors are trimmed to length and inserted into a channel before crimping, and feed-through (pass-through) plugs, where each conductor runs the full length of the plug and is trimmed flush after crimping. Feed-through plugs are popular in the field because conductor alignment is easier to see and get right before crimping, which reduces miswires on tight installation schedules.

Contact plating matters more than it might appear — 50 microinches of gold over nickel is a common commercial-grade spec, since gold resists oxidation far better than bare copper and keeps contact resistance low over thousands of mating cycles. Shielded RJ45 plugs add a metal shell that connects to a cable's foil or braid shield, which only helps if the far-end connector and jack are also shielded and grounded consistently.

Applications

RJ45 male connectors are used anywhere a twisted-pair cable end needs a modular plug rather than a punch-down termination:

  • Field termination of patch cords to exact lengths on site
  • Factory manufacturing of pre-terminated Ethernet and patch cord assemblies
  • Direct device connections where a keystone jack isn't practical
  • Industrial and outdoor Ethernet runs using ruggedized shielded plugs
  • Data center cross-connect and cabinet cabling built to custom lengths

Specifications

Contact count8P8C, gold-plated contacts (typically 50µ min.)
Category ratingCat5e, Cat6, or Cat6A
Conductor compatibilitySolid or stranded, 22–26 AWG depending on design
ShieldingUnshielded (UTP) or shielded (STP/FTP) shell
Design typeTraditional crimp or feed-through (pass-through)
Housing materialClear, high-impact polycarbonate
ComplianceTIA/EIA-568-C.2, IEC 60603-7
Insertion cycles750+ rated

Installation Tips

Untwist conductors only as far as necessary before inserting them into the plug, keep the wiring scheme (T568A or T568B) consistent at both ends of the cord, and make sure the cable jacket is seated inside the plug body so the crimp's strain relief actually grips the jacket rather than the bare conductors.

Troubleshooting & FAQ

A cord that tests fine but fails intermittently under movement is almost always a strain-relief issue — the jacket wasn't seated in the crimp, so flexing pulls on the conductors themselves. Re-terminate rather than trying to repair a flexing cord.

  • Q: What's the difference between a crimp plug and a punch-down jack?
  • A: A crimp plug (RJ45 male connector) is the removable end of a patch cord that plugs into a port; a punch-down jack is a fixed connector terminated into a wall socket or patch panel using IDC contacts.
  • Q: Can solid and stranded RJ45 plugs be used interchangeably?
  • A: Not reliably — solid-conductor plugs are designed for fixed cable that won't flex, and stranded-conductor plugs for cords that will; using the wrong type shortens the connection's life.
  • Q: Can a Cat6 plug be used on Cat5e cable?
  • A: Yes, physically, but the resulting link performs at Cat5e level since overall performance is limited by the lowest-rated component.
  • Q: Why does gold plating matter on RJ45 contacts?
  • A: Gold resists oxidation far better than bare copper, keeping contact resistance low and connections reliable across hundreds of insertion cycles.
  • Q: What are common RJ45 crimping mistakes?
  • A: The most frequent errors are mismatched wiring schemes between the two ends, conductors not fully seated before crimping, and the cable jacket sitting outside the plug's strain-relief area.
  • Q: Do shielded RJ45 plugs need to be grounded?
  • A: Yes — a shielded plug only helps with EMI if its shell is bonded through a shielded jack or patch panel to a proper ground; an ungrounded shield can do more harm than good.
  • Q: Can an RJ45 plug be reused after being unplugged?
  • A: The plug's locking tab can wear out with repeated flexing, but the plug itself can generally be reinserted many times within its rated mating-cycle count.
  • Q: How do I test continuity after crimping an RJ45 plug?
  • A: Use a basic cable tester or wiremap tester to confirm all eight conductors are connected in the correct order with no shorts, opens, or split pairs.
Patch Cords, Ethernet Patch Cord, Data Sockets, Cat6 Cabling, 110 Wiring Block
Since 2005

Yuyao Simante Network Communication Equipment Co., Ltd.

Yuyao Simante Network Communication Equipment Co., Ltd. offer complete network cabling solutions and optical fiber products integrating design, development, sales and service. The factory has 10 regular and customization production lines, fully automatic injection molding machine 10 sets, semi-automatic injection molding machine 20 units, all kinds of automatic installed machine 8 units, maintaining the stable annual output of more than 9 million.

We specialize in network cabling solutions and optical fiber products integrating design, development, sales and service.
 
Based on the mature research and development system, the quality stability of Simante has been guaranteed at the design source. We have more than 10 engineers and over 30 full-time technical persons who continue to provide their professional value in the position, improving quality and promoting product update. Simante provides specialized integrated solutions for customers to ensure it meets the customer's requirement. Welcome to visit.

17+ Industry Experience
Simante factory
Simante workshop

Our main products include keystone jacks,patch panels, wall face plates, data sockets, etc., and are widely used in structured cabling, network communication, smart home and automation equipment, and other fields. The factory has 10 regular and customization production lines, fully automatic injection molding machine 10 sets, semi-automatic injection molding machine 20 units, all kinds of automatic installed machine 8 units, maintaining the stable annual output of more than 9 million.
 
It is precisely because we are based on the high-end market that Simante has higher requirements for product quality. Not only strictly manage the production, but also meet customers' comprehensive testing requirements for products through good performance testing. We maintain stable export volume in Europe, Australia, Africa, the Middle East and Southeast Asia, and also undertake OEM and ODM projects.
 
Simante, help you create value together!

Work with Loyal

We strive to develop our R&D capabilities and manufacture and provide more cost-effective products to meet your market needs.

  • Product quality assurance

  • Customized solutions

  • Innovative product design

  • Responsible service

Get a Free Quote

Name* Email* Company Your Message*
Recommended Links: RJ45 Connectors RJ45 Keystone Jack Male Connector Supplier

Contact Us

*We respect your confidentiality and all information are protected.